Characterization and Calibration of the CheMin Mineralogical Instrument on Mars Science Laboratory

A principal goal of the Mars Science Laboratory (MSL) rover Curiosity is to identify and characterize past habitable environments on Mars. Determination of the mineralogical and chemical composition of Martian rocks and soils constrains their formation and alteration pathways, providing information on climate and habitability through time. The CheMin X-ray diffraction (XRD) and X-ray fluorescence (XRF) instrument on MSL will return accurate mineralogical identifications and quantitative phase abundances for scooped soil samples and drilled rock powders collected at Gale Crater during Curiosity’s 1-Mars-year nominal mission. The instrument has a Co X-ray source and a cooled charge-coupled device (CCD) detector arranged in transmission geometry with the sample. CheMin’s angular range of 5^° to 50^° 2θ with <0.35^° 2θ resolution is sufficient to identify and quantify virtually all minerals. CheMin’s XRF requirement was descoped for technical and budgetary reasons. However, X-ray energy discrimination is still required to separate Co?Kα from Co?Kβ and Fe?Kα photons. The X-ray energy-dispersive histograms (EDH) returned along with XRD for instrument evaluation should be useful in identifying elements Z>13 that are contained in the sample. The CheMin XRD is equipped with internal chemical and mineralogical standards and 27 reusable sample cells with either Mylar^? or Kapton^? windows to accommodate acidic-to-basic environmental conditions. The CheMin flight model (FM) instrument will be calibrated utilizing analyses of common samples against a demonstration-model (DM) instrument and CheMin-like laboratory instruments. The samples include phyllosilicate and sulfate minerals that are expected at Gale crater on the basis of remote sensing observations.     

高强度钢Domex700MCD焊接性能研究

分析了Domex700MCD焊接性,并通过试验及数据分析表明,在焊接工艺中,采用混合气体保护焊、低合金结构钢焊丝ER69-3,通过控制焊接线能量,运用合理的焊接规范,可获得良好的焊缝机械性能。     

一种Ka频段宽带3dB功分桥的实现技术研究

文章简要介绍了波导宽边耦合3dB功分桥的工作原理，重点阐述四耦合窗Ka频段宽带波导宽边耦合3dB功分桥的仿真设计过程、仿真结果以及最终的实物测试结果。最后得到一个性能优良的Ka频段宽带波导宽边耦合3dB功分桥。     

高应变率下的玻璃钢力学性能的实验研究

利用分离式Ｈｏｐｋｉｎｓｏｎ压杆研究了国产环氧玻璃钢和聚脂玻璃钢在平均应变率约为１０＾３ｓ＾－１下的动态力学性能，给出这两种材料在冲击压缩下的弹性模量和能量吸收率，为新型飞行保护头盔的设计提供了材料的实验依据。     

柔性热膜剪应力传感器水下测量温度修正

柔性热膜微传感器应用于流体壁面剪应力测量时,流体温度对传感器输出有很大影响,因此有必要对工作在非标定温度下的传感器输出信号进行修正补偿。重点研究了水下测量时传感器输出与水温的关系以及温度修正方法。通过分析传感器过热比和流体物理性质与温度的相关性,建立了流体温度与传感器过热比和标定系数的函数关系。在此基础上,提出了一种用于水下剪应力测量的温度修正方法,可以有效减小水温对传感器输出的影响。经实验验证,该方法可以使工作在25℃、28℃水温环境下的传感器输出值与其20℃标定值的相对误差从23．7％和37．1％回落到0．82％和0．83％。     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.     

中介机匣典型故障排除及深度修理

航空发动机中介机匣组件因各种故障而需修理或导致报废的现象时有发生。针对发动机中介机匣分流环裂纹掉块、上部衬套磨损松动、弹性环磨损、同心度检测不合格等故障进行分析研究,提出解决措施,制定满足发动机使用要求的合理技术标准和修理方法。在修理技术方法中,采用挖补补焊方法解决分流环裂纹掉块故障;采用极坐标定位与专用模板衬套相结合的方法提高新品衬套加工精度以解决上部衬套更换新品后装配准确性难题;采用装配过盈销钉和扩口工艺以保证零件的堵孔质量等。结果表明:这些修理措施提高了中介机匣零部件的利用率,延长了其使用寿命,降低了发动机修理成本。     

基于独立桨距控制的电控旋翼主动振动控制

电控旋翼利用桨叶后缘襟翼偏转通过气弹作用带动桨叶变距，从而实现对旋翼的控制。但由于其系统的复杂性，桨叶间易存在扭转刚度和质量不相似，从而引起较严重的旋翼振动。针对该情况，提出了基于独立桨距控制的主动振动控制方法，并以某原理性电控旋翼为算例进行了数值仿真，验证了所提出控制方法对电控旋翼由扭转刚度和质量不相似引起振动的减振有效性，最佳减振水平可达90%。